Chainrings

The Wolf Tooth 107 BCD Chainring for SRAM Cranks is compatible with most new SRAM 1x road cranks that use the 107 BCD spider, including the SRAM AXS Power Meter Spider. This chainring uses the patented Wolf Tooth Drop-Stop B Wide/Narrow tooth profile that is optimized for drop bar bikes. - Fits 107 BCD for SRAM Cranks - Drop-Stop technology prevents dropped chains. On Wolf Tooth's patented wide/narrow chainring, the wide side of the tooth has maximum contact on the drive side which spreads the load and improves chainring life. The narrow side allows clearance for mud and debris while reducing friction. - Cranks that use the 107 BCD spider also use the SRAM 8-bolt interface, which is compatible with Wolf Tooth Direct Mount Chainrings for SRAM 8-Bolt Compatibility: - Fits 107 BCD spiders. - Chainline is determined by the crank model. See manufacturer specs for chainline. - 36t chainring will not work with the 107 BCD Quarq Power Meter - Use Drop-Stop B for all SRAM Eagle, SRAM Road and Transmission (T-Type) Flattop chains, 9, 10, and 11spd chains or 12spd KMC, Connex, Wippermann, Campagnolo. DROP-STOP B Compatible 9, 10, 11, and 12spd SRAM Eagle, 12spd SRAM Transmission (T-type) Flattop, 12spd Campy, 12spd KMC Not compatible with 12spd Shimano HG+ chains

Wolf Tooth was first to market with cyclocross 1x specific chainrings because we saw cyclocross as the perfect use for our Drop-Stop® technology. Since their release, the uses for these rings has expanded beyond cyclocross to commuting, gravel riding, and even full on-road applications with the giant 52t rings. - Fits 130 BCD 5 arm cranksets - Drop-Stop technology. On Wolf Tooth’s patented wide/narrow chainring, the wide side of the tooth has maximum contact on the drive side which spreads the load and improves chainring life. The narrow side allows clearance for mud and debris which reduces friction. - Alternating wide/narrow tooth pattern prevents chain derailment Compatibility: - These rings are for use with 130 BCD 5-arm cranksets. - Do NOT fit on the cranksets for Shimano DA 9000 / Ultegra 6800 - Not compatible with Campy CX10/11. - SRAM Exogram cranksets with inset nut must use stock fifth bolt + spacer(s). The Force CX1 bolt features a fifth bolt with 1x specific shoulder. This kit can be found online. - 38T important note: The chain may contact the spider arm slightly when using the 38T chainring (see last photo in the product images). We recommend filing a small chamfer on the spider arm but you can also just install it and let the chain do the work. This is only an issue with the 38T as the 130 BCD was designed for 39T smallest ring. - Stock 2x bolts will not work. You will need bolts like our 6mm bolts which are optimized for single ring mounting. Tech Specs: - Weight: 38t/52g | 40t/60g | 42t/62g | 44t/79g | 52t/132g - Material: 7075-T6 aluminum - Made in the USA - This 1x chainring and can be mounted in either the inner or outer ring position of a double crankset but can not be used in a 2x setup. - Chainline - The most common mounting is in the outer ring position because of chainstay clearance. The ring centerline is ~2mm from the ring's mounting face so they usually sit about 2mm closer to the frame than the stock big ring (depends on the stock ring) Use Drop-Stop B for all SRAM Eagle, SRAM Road and Transmission (T-Type) Flattop chains, 9, 10, and 11spd chains or 12spd KMC, Connex, Wippermann, Campagnolo. Recommendations - If you plan to ride in very muddy conditions, we recommend a chainguide or chainkeeper in addition to a clutch-type rear derailleur. Without these precautions, you may experience chaindrops and/or chainsuck.

The direct mount chainrings for SRAM cranksets with the 3-bolt mounting interface. They replace your existing spider and chainring with one clean looking, lightweight, and stiff piece of machined billet. They are available in the Drop-Stop B tooth profile, which is optimized for SRAM Flattop chain. It is also compatible with all other 9-, 10-, 11-, and 12-speed chains except the Shimano 12-speed chain. Compatibility: - These direct mount chainrings will replace your existing chainring and spider or replace the direct mount ring on SRAM cranksets including the DUB cranks. The ring is attached via 3 bolts on the back side of the spider near the spindle. Note that these chainrings are NOT compatible with SRAM 8-bolt direct mount cranksets. - Wolf Tooth's patented Drop-Stop® wide/narrow tooth profile for the ultimate chain retention and mud shedding ability - There is one offset: Standard Road/CX/Gravel: 6mm offset for cyclocross and road crank applications with 47mm chainline - Praxis Works Road/CX cranks use the 6mm offset. - If using a 9-speed drivetrain, use a 10-speed chain (shifts and works well on a 9-speed drivetrain and fits the ring tighter for better chain retention). Available in multiple tooth profiles for optimal performance based on your chain type. Use Drop-Stop ST for use with Shimano 12-speed Hyperglide+ and 12spd KMC chains. Use Drop-Stop A for all 9, 10, and 11spd chains or 12spd SRAM Eagle, KMC, Connex or Wippermann chains. Drop-Stop B is optimized for SRAM 12 spd Transmission (T-type) and Road Flattop chains but is compatible with all chains that work with Drop-Stop A. DROP-STOP B - Compatible 9, 10, 11, and 12spd SRAM Eagle, 12spd SRAM Transmission (T-type) Flattop, 12spd Campy, 12spd KMC - Not compatible with 12spd Shimano HG+ chains Recommendations - - Recommend the use of a clutch style rear derailleur for the best chain security. - An L-wrench works best since the crank spindle may contact a socket adapter and prevent it from engaging properly. - Use the same 3 bolts to attach the Wolf Tooth ring or we carry replacement bolts Tech Specs: - Weights: 38T/90g | 40T/106g | 42T/111g - Material: 7075-T6 aluminum - Made in the USA